|
1979-1995
4RUNNER/PICKUP STEERING
 High
Steer Crossover Kit w/ 6 stud arms
Over a year in development and
testing, this new knuckle design sets a new standard in Toyota knuckle
strength and reliability. This kit totally eliminates the problem of
broken steering knuckles and studs. The addition of two studs in each arm
effectively prevents the steering arm from becoming loose and shearing off
the studs. The knuckle housing is also thicker then stock and larger
gussets have been added around the outside of the knuckle for extra
strength. Precision CNC machined, each knuckle is direct bolt on, heavy
duty replacement.
 Six
Stud Knuckles are sold as a pair and include our set of special 6 hole
shims for use between the top of the knuckle and the steering arm. Also
included is a 1/2" course thread bolt to help remove the steering arms for
knuckle service. To remove the steering arms, remove all 6 nuts, then
install the bolt in the top of the arm. As the bolt is tightened, the
steering arm is pulled up off the knuckle. Stock lower bearing plates and
shims from your old knuckles are needed for knuckle assembly. A minimum of
four additional steering arm studs are needed for installation. Six Stud
Knuckles are a Marlin Crawler design and are manufactured exclusively by
Trail-Gear Inc. No questions asked, lifetime warranty on all knuckles,
arms, rod ends and rods.
 Our
six stud high steer kit includes left and right six stud steering arms,
tie rod, drag link, four rod ends and your choice of flat or curved pitman
arm. To use this kit you will also need an IFS style steering box, box
mount, and Six Stud Knuckle Kit, four additional knuckle studs.
 Knuckle
studs, nuts and washers can be found on our
axle page.
Six Stud Knuckle Kit - $249 + $30 S/H
High Steer Kit w/ 6 stud arms - $399
+ $45 S/H
High Steer Arms w/ 6
studs - $199 + $25 S/H
Six Stud
Knuckle Shim Pack - $10 + $5 S/H
 High
Steer Crossover Kit w/ 4 stud arms - $299 + $45 S/H
Crossover Steering is critical for rock crawling. The stock steering just
can't keep pace with today's super flexible suspension systems. This
results in broken stock steering arms and loss of steering. Kit
features super beefy, solid forged steering arms, heavy duty pitman arm,
heavy duty .250 wall steering rods, and greasable ends. Precision fit for
easy assembly. Comes with standard or flat pitman arm.
 High
Steer Arms w/ 4 studs - $129 + $25 S/H
Each arm is pressure Forged from 8620 tool steel, these arms are
incredibly strong. All mounting surfaces are machined including the
split washer surface and the tie rod tapered holes, ensuring correct and
positive contact between parts, preventing knuckle studs and tie rod ends
from coming loose. Arms are angle compensated so that the rod ends ride at
the factory designed 90 degree angle. Fits 1979-1985 Toyota pickup and
4Runner. Also fits 1979 and later Land Cruisers with spring over
conversion.
Standard
Pitman Arm
Solid one piece design. Features FJ80 tapered hole. One piece, forged
design. Extra strong, wide design. Ideal for use with crossover steering.
 Standard Pitman Arm - $69
+ $10 S/H
 Flat
Pitman Arm - $69 + $10 S/H
 Sector
Shaft Nut & Washer
Replacement nut and washer for bolting on pitman arm to steering box. Fits
4wd IFS steering box from 1986-1995 Pickup and 4Runner.
Nut, Sector Shaft - $3 each + $1 S/H
Washer, Sector Shaft - $2 each + $0.75 S/H
 Tie Rod
& Drag Link
Our heavy duty tie rods and drag links. Made from .250" wall DOM
1.25" tubing. Precision tapped. Left side thread mark. Each
rod is test fitted to ensure rod ends thread in with correct fit.
Powder coat black finish. Fits 79-95 Pickup/4Runner with crossover
steering.
Tie Rod - $59 + $20 S/H
Drag Link - $59 + $20 S/H
 FJ-80
Tie Rod End
Heavy duty FJ-80 tie rod ends are ideal for Toyota crossover steering
applications. Zerk fitting in the bottom allows for easy greasing.
Includes cotter pin and jam nut.
FJ-80 Tie Rod End, right hand thread - $20 + $5 S/H
FJ-80 Tie Rod End, left hand thread - $20 + $5 S/H
 Steering
Pump Kit - $399 + $40 S/H
The stock Toyota pump is just barley able to supply the volume and
pressure needed to run hydraulic assist steering. The stock pump puts out
1,300 psi @ one gallon per minute. The stock pump is not able to provide
enough fluid to run both the stock steering and the demands of a ram,
especially at low rpms. Drilling out the restrictor plates in a stock pump
for more volume often leads to pump failure. This pump provides the full
fluid volume your steering box and ram are looking for, even at an idle.
Kit
includes: pump, pump bracket, reservoir, reservoir bracket, belt, fittings
hoses, & hardware. Pump kit is designed to work with stock or ram drilled
IFS power steering boxes.
Application Notes: This pump and bracket is designed to fit all Toyota
4cyl 4wd motors from 1979 - 1995. A large power steering fluid cooler
(included) is required on the low pressure side of the system. Pump
bracket works in conjunction with stock idler bracket. If your truck is
not currently equipped with power steering, you will need to purchase the
idler bracket and replace the steering gear box with one designed for use
with power steering. The stock fan belt will not work with this pump and
will need to be replaced with the belt included with the kit.
 IFS
Steering Box Mount - $39 + $10 S/H
If you're installing crossover steering on your 79-85 4wd Toyota you're
going to need to mount an IFS steering box. This frame mount kit
includes both inner and outer frame reinforcing plates, grade 8 bolts, DOM
tubing, and crimp nuts. Inner plate is 1/4, outer plate is 3/16".
Angled leading and trailing edges prevent frame cracking. Heavy duty
design.
 IFS
Steering Boxes
High quality remanufactured IFS boxes for your crossover steering.
For crossover steering on 79-85 trucks we recommend the early style box
but you can also use the late style if you wish. Early style (left
in photo) fits 86-88 Pickup and 86-89 4Runners. Late style box
(right in photo) fits 89-95 Pickup and 90-95 4Runners. All boxes are
completely rebuilt with new seals and bearings. Each unit is tested
before shipping.
IFS Steering Box 86-88 - $299 + $30 S/H
IFS Steering Box 89-95 - $399 + $30 S/H
 Hydro
Assist IFS Steering Box - $399 + $30 S/H
Toyota IFS steering boxes that are drilled and tapped for hydro assist
steering. Two # 6 JIC fittings are installed. After tapping, each box is
thoroughly flushed and fully rebuilt. 1986-1988 Style box.
 Hydro
Assist Steering Kits
Hydraulic ram with high temp inner and outer seals for long life and
no leaks. Our specially designed ram features a 3/4" rod that is 50%
stronger then other 1/2" rods on the market. Six inch application for
Toyota knuckles. Eight inch application for Dana knuckles. Included with each
ram kit:
* Ram with high temp inner
and outer seals
* Rod ends w/jam nut
* Ram bracket for axle housing
* Ram bracket for tie rod
* (2) Hoses
* (2) JIC 90 degree elbows
* Mounting Hardware
* Instructions with photos
Hydro
Assist Steering Kit, 1.5" x 6" - $199 + $25 S/H
Hydro
Assist Steering Kit, 1.5" x 8" - $199 + $25 S/H
Hydro
Assist Steering Kit, 2" x 6" - $219 + $25 S/H
Hydro
Assist Steering Kit, 2" x 8" - $219 + $25 S/H
Kits
require 1.25" OD cross over steering tie rod and drilled and tapped IFS
steering box (both sold separately above).
Hydro Assist Installation Instructions
 Hydro
Ram
Hydraulic ram with high temp inner and outer seals for long life and no
leaks. Our specially designed ram features a 3/4" rod that is 50% stronger
then other 1/2" rods on the market. Ram requires rod ends, sold
separately. Six inch application for Toyota knuckles. Eight inch
application for Dana knuckles.
Hydro Ram, 6" x 1.5" - $140 + $15 S/H
Hydro Ram, 8" x 1.5" - $160 + $15 S/H
Rod End, 5/8", Male - $16 + $5 S/H
Rod End Jam Nut - $2 + $1 S/H
Rod End, 5/8", Female - $16 + $5 S/H
 Hydraulic
1/4" Pipe Plug - $1 + $0.25 S/H
These 1/4" pipe plugs are used to block the ram ports of steering
boxes. Once installed, a tapped box can be used without a ram.
If you have a ram kit, these can be a good item for your tool kit in case
of ram or hose failure.
 Hydraulic
Hose
Heavy-duty high pressure Hydraulic hose. JIC-6 Ends. Can
be used with our without 90 degree fitting depending on application.
High quality crimped connections for long life. Hoses go from
steering box to ram.
Hydraulic Hose, Steering - $15 + $5 S/H
Elbow fitting, 90 degree JIC - $7 + $1 S/H
 Brackets
Looking for brackets to mount your ram? Check out ours! We
have a nice set of heavy duty 1/4" plate steel brackets that are easy to
install on your tie rod (1.25") and axle housing. No grinding tabs
to fit with these perfectly shaped brackets. Hole size is 5/8".
Hydro Bracket, Axle Housing - $15 + $5 S/H
Hydro Bracket, Tie Rod - $15 + $5 S/H |
